Leveraging IT for Access Control

Solutions that use 13.02 FICAM topology eliminate the need for proprietary access control panels

Trying to navigate through the numerous security regulations that are in place for government agencies and facilities can be a daunting challenge, even to the most seasoned security professionals. Buying access control solutions that are compliant with federal mandates, such as HSPD-12 or FIPS-201, means there are only a select few products that end users in the government sector can purchase. The only way to ensure these purchased solutions are in compliance with these requirements is to turn to the General Services Administration’s (GSA) approved products list (APL).

But even then, there are still budgetary constraints that may make implementing the best access control system nearly impossible, and government end users are still faced with the prospect of investing a significant amount of money to upgrade their existing access control infrastructure without a reasonable ROI.

Requirements Abound

In the past, government facilities could implement low-cost access cards and readers as a simple means of securing doors. Now, they are required to have a particular type of smart access card—usually a personal identity verification (PIV) card—and that card has to be authenticated at the reader. This means that the system has to check to determine that each card hasn’t been duplicated or spoofed; hence, there are many requirements in place at certain facilities to deploy some type of biometric credential solution in conjunction with the traditional card access system. Some even require the use of a PIN number in addition to these other layers.

All of these things have amounted to increasing costs across the government spectrum as agencies have sought to create secure digital identities for employees, most of who are required to be fingerprinted, photographed and issued cards that have digital certificates linked to them.

The quandary for many in the market has been how to link this new generation of secure credentials with existing physical access control systems (PACS) infrastructure, card readers, control panels and the like. The problem is that the majority of these products are on the lower end of the access control technology spectrum, specifically control panels, and don’t have the capability to check and see if a card is fraudulent at the time it is presented.

One of the major hurdles federal officials ran into is that after agencies went on the APL and purchased the components necessary to achieve this new level of required security, they quickly found many of these solutions were incompatible with one another. In response, the government introduced a new program called Federal Identity, Credential, and Access Management or FICAM that outlines the requirements of an end-to-end access control solution in which all of the devices are interoperable with one another.

Two Different Topologies Offered for FICAM Compliance

Historically, most of these systems—identity, credential management, logical access and physical access—operated in silos and did not work very well together. With FICAM, the GSA is attempting to create a new level of interoperability between these solutions.

Topology 13.01. One of the options available to address this issue is that of an additional hardware component being installed between the reader and the control panel that has all of the intelligence necessary to check the card and ensure that the credential is authentic. It does this by leveraging the IT network to verify the information on the card, and checks if the credential has been reported as lost or stolen.

This method includes three categories of components: the card reader, the access control system or the PACS, and the intermediary validation system between the reader and the panel.

Topology 13.02. This is a completely new architecture that is optimized for leveraging an IT infrastructure to meet the FICAM requirements by “virtualizing” the PIV and PIV-I credential certificate validation and authentication functionality within the access control software. Physical access points are controlled using IP encryption bridges to connect door hardware and transform card readers into IP addressable devices. This topology was introduced as an alternative to the 13.01 topology because it does not require the additional hardware and third party software needed to add authentication and validation capabilities to traditional control panel systems. Credentials are presented at the reader and cryptographically challenged by the Freedom 1302 PACS and Validation software. These credentials are then authenticated and validated before an authorization check is performed to grant or deny access to the cardholder.

This unique approach eliminates the need for an intelligent hardware component that would otherwise be necessary to meet the requirements for FICAM by using a traditional PACS architecture. All data is encrypted to eliminate the opportunity for cyber threats, ensuring that a high-level of security is maintained to meet one of the stringent testing requirements of FICAM-approved products.

The Benefits of Using an IT-centric Solution

In an IT-centric environment, solutions leverage software running on hardware as opposed to firmware-supported hardware, which is counter to how things typically work in government access control applications. For the end user, they’re able to take their existing IT infrastructure (TCP over IP) and run software on it to control their access control system in the same way they control network security for logical access to computers.

Using an IT-centric solution also provides users with significant costs savings, which is an issue when dealing with clients that have strict budgetary requirements like the government. Because much of the hardware that’s required in a traditional access control system is unnecessary under this kind of architecture, end users do not need to have the antiquated devices that would typically be required.

For instance, a solution that runs on the IT network doesn’t require the use of any proprietary access control boards or panels to perform the authentication check at the door that other systems require. The user only needs the computers operating in their data bank running software with some type of interface at the door to connect the electric-strike contact, monitor whether or not the door is open and have a push button that people can use in the event of an emergency to exit the building.

Another potential drawback in using a solution that relies on panels is that even when the devices are supplemented with an intelligent component to complete the credential validation process, the technologies still do not have access to the real-time data that a solution using the IT-centric model does. When it comes to interoperability and the time it takes for validation of a credential, the 13.02 topology can interact with these other systems much faster to determine what policies or attributes may have changed, and make that decision quicker than a typical panel-based solution.

Why Buying FICAM-compliant Products Matters

Because federal agencies are required to purchase products on GSA’s approved products list, any type of PACS solution—be it a traditional hardware-based system or one that is IT-centric—needs to have previously achieved FICAM approval before it is deployed. Having this approval paves the way for the deployment of various access control products in all federal agencies as well as all buildings leased by the GSA for other federal agencies.

Although the user is limited in what they can implement in their facility by what products are on the APL, they are protected. They can rest assured that what they do purchase works, is not vulnerable and meets all of the compliance checklist items.

The rigorous FICAM test program ensures that each product on the GSA’s APL meets the functional requirements of FIPS 201 and NIST SP 800-116, that the system is secure from a network perspective, and that there is complete interoperability between all topology components.

Evaluating FICAM’s Impact on Government End Users

At the end of the day, government users are looking for solutions that meet the necessary requirements at the lowest possible cost. Each agency has a prime directive, be it serving veterans, retirees or ensuring homeland security, not spending millions and millions of dollars on access control measures.

While the government has had access control mandates in place for well over a decade, there are still a number of agencies that have yet to fully meet all of the requirements. However, with FICAM, the GSA has said that all access control products purchased moving forward must meet these standards or else they won’t be approved for use in buildings owned or operated by the federal government.

Eventually, everyone in the government sector is going to move toward interoperability in physical access, logical access and identity management. The best way to accomplish this is through the deployment of a solution that takes advantage of the IT infrastructure already in place.

This article originally appeared in the October 2014 issue of Security Today.


  • Cloud Adoption Gives Way to Hybrid Deployments

    Cloud adoption is growing at an astonishing rate, with Gartner forecasting that worldwide public cloud end-user spending will approach $600 billion by the end of this year—an increase of more than 21% over 2022. McKinsey believes that number could eclipse $1 trillion by the end of the decade, further underscoring the industry’s exponential growth. Read Now

  • AI on the Edge

    Discussions about the merits (or misgivings) around AI (artificial intelligence) are everywhere. In fact, you’d be hard-pressed to find an article or product literature without mention of it in our industry. If you’re not using AI by now in some capacity, congratulations may be in order since most people are using it in some form daily even without realizing it. Read Now

  • Securing the Future

    In an increasingly turbulent world, chief security officers (CSOs) are facing a multitude of challenges that threaten the stability of businesses worldwide. Read Now

    • Guard Services
  • Security Entrances Move to Center Stage

    Most organizations want to show a friendly face to the public. In today’s world, however, the need to keep people safe and secure has become a prime directive when designing and building facilities of all kinds. Fortunately, there is no need to construct a fortress-like entry that provides that high level of security. Today’s secured entry solutions make it possible to create a welcoming, attractive look and feel at the entry without compromising security. It is for this reason that security entrances have moved to the mainstream. Read Now

Featured Cybersecurity


New Products

  • PE80 Series

    PE80 Series by SARGENT / ED4000/PED5000 Series by Corbin Russwin

    ASSA ABLOY, a global leader in access solutions, has announced the launch of two next generation exit devices from long-standing leaders in the premium exit device market: the PE80 Series by SARGENT and the PED4000/PED5000 Series by Corbin Russwin. These new exit devices boast industry-first features that are specifically designed to provide enhanced safety, security and convenience, setting new standards for exit solutions. The SARGENT PE80 and Corbin Russwin PED4000/PED5000 Series exit devices are engineered to meet the ever-evolving needs of modern buildings. Featuring the high strength, security and durability that ASSA ABLOY is known for, the new exit devices deliver several innovative, industry-first features in addition to elegant design finishes for every opening. 3

  • Camden CM-221 Series Switches

    Camden CM-221 Series Switches

    Camden Door Controls is pleased to announce that, in response to soaring customer demand, it has expanded its range of ValueWave™ no-touch switches to include a narrow (slimline) version with manual override. This override button is designed to provide additional assurance that the request to exit switch will open a door, even if the no-touch sensor fails to operate. This new slimline switch also features a heavy gauge stainless steel faceplate, a red/green illuminated light ring, and is IP65 rated, making it ideal for indoor or outdoor use as part of an automatic door or access control system. ValueWave™ no-touch switches are designed for easy installation and trouble-free service in high traffic applications. In addition to this narrow version, the CM-221 & CM-222 Series switches are available in a range of other models with single and double gang heavy-gauge stainless steel faceplates and include illuminated light rings. 3

  • Compact IP Video Intercom

    Viking’s X-205 Series of intercoms provide HD IP video and two-way voice communication - all wrapped up in an attractive compact chassis. 3